Please visit our home site at

Anke and I live aboard WAYWARD, and wrote about it's design and construction at

Access to the net comes and goes, so I'll be writing in fits and spurts.Please feel free to browse the archives, leave comments where you will and write... I'll respond as I can.

Fair winds!

Dave and Anke
triloboats swirly gmail daughter com

Saturday, January 30, 2016

Considering Multihull TriloBoats


Verrrrry interesting.... but STUPID.
-- Arte Johnson (I'm half kidding) 

Considering Multihull TriloBoats

Judging by the amount of correspondence I field on the subject, there's a fair amount of interest in multihull TriloBoats – catamarans (cats), trimarans (tris) and proas. 

Here, I'll lay out the modest benefits and considerable pitfalls I see in this approach at cruising sizes, along with an impressive example of a smaller scale project that I consider highly successful.

I warn you... this is rather dull going. Unless you're particularly interested, I'd bail.

A bit of jargon: Amas are the longitudinal 'hulls' composing a multihull. There's some variation in use about the net, but it seems a pretty generally accepted term.

NOTE: The T40x20 CATAMARAN, shown above, was a 'cartoon' made on request for relatives who'd fallen in love with Phil Bolger's DOUBLE EAGLE. It's way beyond my engineering skills to even put it out as a design, but gives a taste of a square boat approach.

I should emphasize that this approach is not our taste, in general. Anke and I would be off on a Wharram TIKI, or at least a dory-ish trimaran if we ever succumbed to the allure of polyhullery and warm waters.

Multihull Principles

The use of multiple hulls is primarily to greatly improve stability. They may follow one or a mix of two strategies:

Float the leeward ama – Its reserve displacement resists heeling moment, tending the whole to low angles of heel. Its wetted surface and resulting drag, however, slow the vessel and induce lee helm.

Hike the windward ama – Its weight, lifted at the long end of a lever arm, resists heeling moment, tending the whole to low angles of heel. Lifting up and clear of the water's surface reduces wetted surface and resulting drag, as well as hull-dynamic weather helm, optimizing speed.

Cruising catamarans favor the first strategy, while proas favor the second, as do most racing or speed maximizing craft. Trimarans mix the strategy, and tend to work with shorter lever arms.

The longer and leaner the hull(s), the faster the vessel can be. Wharrams suggest a minimum of 11:1 length to waterline beam ratio. Such hulls are easily driven to higher-than-displacement speeds. Extremely narrow hulls with very high freeboard (over low draft) are enabled by the amas, which keep them from flopping over onto their sides.

Circular hull sections are fastest, but have low lateral resistance and can't be easily built of sheet materials. Rectangular sections carry the most load (assuming equal beam and draft), and have high lateral resistance. V sections have good lateral resistance and speed, but low displacement on a given draft.

Long and narrow has ergonomic consequences. In order to have a wide enough interior to fit even a snug double berth within a fast hull, the hull quickly gets long. Flare above the waterline can help, but a platform must be placed high to take advantage, reducing its headroom. The interior is linear, in shorter hulls, with little opportunity for circular social settings below-decks.

A common solution is to live largely on top of the hull/ama(s)/deck. But this generates considerable superstructure which adds weight and windage.

A mixed strategy is often employed... low superstructure to provide headroom over the narrow hull, into which, perhaps, only feet may dangle. It may overhang the sides to help provide 'elbow-room', storage or even low headroom bunks.

Wharrams recommend a 3ft sea-riding height for bluewater cats (I take that as applying generally to multis), measured from the waterline to the underside of decks between amas.

Caveat to Multihulls vs Monohulls

Here are some for DIY builders to consider when comparing types:

For a given footprint, a multihull adds cost, complexity and engineering challenges.

You are building two to three monohulls, cross beams to join them, with one or more decks and/or superstructures over. Each of these components represents a fair chunk of the effort required by a monohull. Special challenges – like mast steps, Ackermann steering, high leverage forces throughout – make design daunting to dangerous for the amateur. Everything multiplied x multi.

In terms of square sections, things get scarier... the initial and reserve buoyancy of a slab is much higher than usual sections. Larger forces develop faster than the usual rules-of-thumb were evolved to handle.

If one joins the very few pioneers in this field, I recommend a cautious approach, backed by modelling, certified expert advice and incremental sea-trials.

The payoffs are speed(!) under sail, humongous decks and undeniably cool. For the pure of heart, able to run lightly through the world, multihulls can more than pay their way.

So, with that caveat, let's continue...

Simple Conversions: Adding Outriggers to Square Boats

Adding amas to a full-width TriloBoat designed as a cruising hull, I feel, is a losing proposition.

Triloboats and other box barges already have the highest monohull form stability possible on a given footprint (length x beam x draft).

As cruisers, box barges skim upright downwind, benefitting from shoal draft relative to their displacement (don't have to push much water aside). On the wind, they benefit from heeling by presenting a V section to the water.

A simple, multihull conversion detracts from both. The outrigger(s) add displacement and drag off the wind, and force the hull more upright on the wind. Plus, they clutter the deck, increase the beam with high windage, vulnerable bits, and – starting from the high mono-deck – don't offer usable sidedecks.


Critiquing the T40x20 CATAMARAN

Let's take for granted that my T40x20 CATAMARAN can be well-engineered to be affordably and soundly built.

Even so, the two amas together total only 8ft hull beam. Displacement is roughly equivalent, then, to a T40x8 square monohull. But the monohull wouldn't require the two, inboard ama sidewalls. We'd be able to live within the T40x8, rather than on top of it, eliminating much of the superstructure with its weight and windage.

If a large living platform were the goal, converting to a barge by hulling over between amas would increase displacement by roughly 250%, and likely halve construction effort.

Box Section Approach to Multihulls

So let's look at it from the other direction. Could a 'square' multhull be worthwhile, designed from the ground up? This, to my mind, shows much more promise.

Triloboat approaches that might apply:

  • Square sections
  • Constant section
  • Whole and even fractions of sheet materials

These are independent, and can be considered throughout the design.

We'd likely want to start with a long, slender hull, as per multihull normal, for an easily driven hull.

Square sections carry the same weight on less draft than all others. That can be useful. Their right angle chines provide good lateral resistance. They're easy to build, and interiors are easier to fit. Hull mid-bodies benefit most.

But flat bottoms forward – especially when held upright by amas – pound when slapped by the water's surface. What to do?

Fining down the bow - and maybe adding a cutwater (a sharp, faux hull bonded under the bow) - helps a lot with this. I'd consider matching the forward curves in plan and profile (TAB) for least turbulence.

I doubt the stern needs to narrow, and full width preserves precious deck space at the transom. I'd consider a very easy exit, with the bottom of the transom at or slightly above the waterline. Being a multihull, we're not going to heel much (so won't drag the transom corners), while the release wave depresses to help match the exit angle. Never actually seen this in square hull action, so needs experiment.

Constant sections – of whatever shape – naturally develop parallel longitudinal lines (such as the sheer) along the constant section. This is especially useful amidships, with superstructure planned and fit along this stretch.

Constant section amas , with shaped foam ends (where shapes get complex) and glassed over, show promise, I think, for easy construction and good performance. I'd personally favor assymetrical V sections (especially Newick plow-style), with the leeward face(s) oriented vertically for lateral resistance.

Whole and even fractions of sheet materials can be applied to hull, superstructure and decks, for economies of effort an material.

Another approach to square sections might be to rotate the square sectioned hull 45deg, for an upright V section. We'd end up with a diamond-style section resembling Superman's chest logo (variations are possible). The right-angle keel would run the entire centerline, eliminating any need for a cutwater at the bow. Downside is increased draft for the same displacement.

A Square Trimaran: (Mostly) A Success Story

Mark Meyer designed and built an upright box section trimaran at 27 feet. It is wicked fast, fun, good looking (I think) and carried his family safely across the waters of northern Southeast Alaska. He used it extensively to fish Tenakee Inlet for at least a decade.

Notably, he used square section, aluminum girders, rigidly mounted, for cross-beams. These worked very well.

His only disappointment were the flat-bottomed amas – skimming across the water they pounded hard. He added a V section cutwater toward the bow, which improved the situation, but not much. Apparently, flat-bottomed, flying amas proved to be a poor choice.

NOTE: Wharram Designs abandoned flat-bottoms for their catamarans for the same reason... the windward ama raised enough to pound badly. Nevertheless, they safely travelled far and wide.

Mark definitively proved the concept for the main hull, and new amas were in the works last I checked in. 

My personal opinion is that  square sections are a viable choice for hulls that stay immersed, especially when building quick and dirty or on a small scale. 

I, myself would opt  for other shapes in any project large enough to represent a significant investment. It seems to me that, beyond a certain point, the savings in construction effort cut into long-term multihull values.

But that's me.


So there you are, dear Readers. For those of you interested in these exotic pursuits, I wish you happy doodling.

And keep me posted!


  1. Hi Dave,

    Synchronicity (n.) – “the coincidental occurrence of events and especially psychic events (as similar thoughts in widely separated persons or a mental image of an unexpected event before it happens) that seem related but are not explained by conventional mechanisms of causality – used especially in the psychology of C. G. Jung” (Webster)

    * Though other questions of mine have received more attention from me, the one of multihull triloboats has been on a quiet but persistent backburner. Your synchronous blog post hit the spot there.

    * Since you don’t have a blog post titled, “So, How Cool Am I?”, I’ve been pondering which random post to use to drop a general compliment into. And just when I went to look through your blog in earnest … I found this new excellent example and potential compliment bucket. Nicely done.


    I am inquisitive and capable enough to have been the bane of many of my teachers and answerers-du-jour over the years. Some could not answer. Some did not want to work that hard. A few actually admitted it.

    Over the course of many years and thousands of questions, I’ve noticed patterns. Some patterns seem to mature into conclusions. One of those is the elusive connection between intelligence, knowledge, and teaching talent.

    While far too complex for a blog comment, I’ll summarize. I believe there are positive correlations between intelligence, and capacities for knowledge and teaching talent. However, there are many, many more intelligent, knowledge people who cannot explain or teach what they know to save their lives than the opposite. I encounter them regularly. Even when I redesign and simplify the question for them repeatedly, and serve it up as if we’re playing T-ball, they just can’t hit it. A conundrum for sure.

    On the other hand, there are relatively few, with seemingly equal intelligence, who can use their accumulated knowledge and better understanding in an uncommonly useful way. They manage to overcome the standard “it depends” obstacle that stops so many others. They manage to hold their egos in check and to avoid showboating their superiority. They manage to actually take a minute to consider what the other person needs vs. what they themselves want to say. They are successful at squeezing themselves like an orange to produce the drops of juice most salient to a situation, leaving the rest behind, and passing those drops on to others in a way that meets the less knowledgeable person where that person is, not where they themselves are. Having cracked the code on what it actually means, they alone are worthy of the title of ‘teacher’.

    You, Dave, are that rare, valuable second type of person. That is your gift (and sometimes your curse ;-), and you share it willingly. This blog post is but one small example of that.

    I thank you for it.



  2. I'll add to the litany of adulation by saying, from personally seeing it on numerous occasions, that the way you demolish a package of store bought cookies is highly admirable. Not my personal choice for boatbuilding fuel but, hey, it sure seems to work for you. In fact, perhaps fodder for another essential boat building cog blog post: the prime role of a rack of store bought cookies for efficient marine construction.

    All that aside I'd add that some of Gary Dierkings outrigger canoes are essentially long and lean trilo hulls and do quite well. We're talking proas here basically and with a bit more heel than cats. In addition a proas connecting beams are much less stressed thus less materials. And the much necessary floatation bubble that hangs off the leeward side would be easy to construct on a squarish trilo hull. Proven to be very safe at sea in knockdown situations! It would have to be fairly long to get any real interior space but the beauty of multis, besides their cushy-magnificent ride offshore, is in-harbor tropical sprawl space. With awnings here and there, and a shitpot of kayaks and tenders on deck, what a nice home in some tropical archipelago.

    Lastly, Gary Leepaks bi-plane junk rigged cat "Dragon Wings" had 7.5 to 1 hulls. It performed well (semi-V hull though) and he traded speed for that wonderful cat ride. If one is down with this trade-off (wise in a time of random lost shipping containers dotting the worlds oceans) then it can apply to a host of multihull designs.

    Never say never..... trilos have great potential for multihull configurations. Just needs a pioneer to fine tune the concept in the real world.

    1. "I'll add to the litany of adulation by saying, from personally seeing it on numerous occasions, that the way you demolish a package of store bought cookies is highly admirable. Not my personal choice for boatbuilding fuel but, hey, it sure seems to work for you. In fact, perhaps fodder for another essential boat building cog blog post: the prime role of a rack of store bought cookies for efficient marine construction."

      The impact on my 'adulation' level would of course depend on the flavor of cookie.

    2. Shucks, Y'all, ya make me blush.

      But I do love a cookie... I'm a weak man.



    Slender barge hulls make great proa vakas!

    1. Hi En Proa,

      The Vaka is the main hull of a proa? I see that the ama (outrigger, if I have the term right) looks to be a V hull?

      Nice model!

      Dave Z

  4. I keep coming back to this post, Dave.... incredibly romantic to figure out a 48X4 box proa. Good info here to harvest. December 23rd, 2016.

  5. Dave,
    I've often thought of Box shaped hulls for a catamaran, I'm not sure if if the dream came from this post or I found this post running down a dream...
    Instead of box/barge front end, why not keep the bottom flat and bring the hull sides to a point at the stem? Should be a nice slicing entry into the waves. At 48x4 I don't see the windward hull flying and presenting the pounding problem, but I'm not at all experienced with catamarans. Perhaps a mast in each hull to keep the CE low would keep the lift on the windward hull minimal. My wife will tell you that I'm both stubborn and dumb enough to actually build one of these.
    I've been vacillating between a T32x12 and Wharram Tiki 37 and I can't really seem to make up my mind. Just when one idea has a set itself in my head, something comes along and brings the other idea to the fore.
    Anyway the goal is to do the great loop, sooner rather than later.
    Thanks for the blog!

    1. Hi Tim,

      I agree with pointy bows for multihulls... the doodle at the beginning of the post is as you suggest. Cutwaters are relatively easy to add, and these can help, too.

      It's possible on larger hulls that the forefoot can be kept below the waterline. Benford dories, for example, do this without apparent problems. That would certainly help.

      Happy wife; happy life! Good luck with decisions.

      Dave Z

  6. This recently in:

    Michael Schacht, a designer of considerably more skill than myself has designed what looks to me to be a fully functional, square-section trimaran, based on rotating the section 45deg (as described in the post, above).

    You can read about it, here:

    Dave Z